1. Refer to the exhibit. What device does Device X represent in the graphic to allow PC1 to ping PC4?

hub
router
bridge
access point
Layer 2 switch

2. Refer to the exhibit. How many collision domains are present in the topology?

3
5
6
7
8
9

3. A company has the following addressing scheme requirements:

-currently has 25 subnets
-uses a Class B IP address
-has a maximum of 300 computers on any network segment
-needs to leave the fewest unused addresses in each subnet

What subnet mask is appropriate to use in this company?

255.255.240.0
255.255.248.0
255.255.254.0
255.255.255.0
255.255.255.128
255.255.255.248

4. Refer to the exhibit. A network administrator attempts to increase the available bandwidth for workstation A by setting the NIC to full-duplex mode. After the configuration is changed, there are increased collisions and errors occurring. Why is this occurring in the network?

The NIC is no longer detecting collisions.
The switch will not support full-duplex mode.
The hub will be continually producing a jam signal.
The cabling will not support bidirectional transmissions.

5. Refer to the exhibit. A newly hired technician has a task of terminating CAT 5 UTP cables. The network administrator visually examined the cables the technician terminated. Some of the cables have connectors as shown in the exhibit. What should the network administrator explain to the technician about the cables?

Both cables are acceptable.
The cable in Graphic A will produce more crosstalk.
The cable in Graphic A should be used in the more critical network segments.
The cable in Graphic A is preferred because it will be easier to crimp the connector.

6. Which technologies are considered to be WAN technologies? (Choose two.)

Ethernet
DSL
Token Ring
Frame Relay
FDDI

7. A simplified CAM table for Switch1 is shown in the exhibit. If host A sends a frame with a destination MAC address of 66C, how does the switch process this frame?

The switch drops the frame.
The switch sends the frame out port 3.
The switch sends the frame out ports 1, 2, and 4.
The switch sends the frame out ports 2, 3, and 4.
The switch sends the frame out ports 1, 2, 3, and 4.

8. Refer to the exhibit. What must be configured on Host B to allow it to communicate with the Host C? (Choose three.)

the MAC address of RTA router interface connected to Switch 1
a unique host IP address
the IP address of Switch 1
the default gateway address
the MAC address of Host C
the subnet mask for the LAN

9. Refer to the exhibit. The connections in the exhibit are labeled A through E. Which of these indicate WAN links? (Choose three.)

link A
link B
link C
link D
link E

10. Which of the following increases the potential for a collision to occur?

the use of an active hub instead of an intelligent hub
the use of an intelligent hub instead of an active hub
a reduction in the number of devices attached to the hub
an increase in the number of devices attached to the hub

11. Refer to the exhibit. What type of cable connects the two routers together without any intermediary device?

console
rollover
crossover
straight-through

12. A NIC of a computer has been assigned an IP address of 172.31.192.166 with a mask of 255.255.255.248. To which subnet does the IP address belong?

172.31.0.0
172.31.160.0
172.31.192.0
172.31.248.0
172.31.192.160
172.31.192.248

13. Refer to the exhibit. Which type of Category 5 cable is used to make an Ethernet connection between Host A and Host B?

coax cable
rollover cable
crossover cable
straight-through cable

14. Refer to the exhibit. Host A has been added to the network. However, host A cannot communicate with the server B or the Internet. All cables have been tested and are functioning to standards. At which layer of the OSI model is this problem occurring?

Layer 1
Layer 2
Layer 3
Layer 4

15. Refer to the exhibit. Workstation 1 pings the Fa0/1 interface of Router 1. Which MAC address will workstation 1 obtain during the ARP request for this communication?

00-06-5B-88-DF-C3
00-B0-D0-7F-F7-46
00-0F-24-85-75-C0
00-0B-E5-64-BD-44
00-08-A3-B6-CE-02
00-08-A3-B6-CE-03

16. What is the correct number of usable subnetworks and hosts for the IP network address 192.168.99.0 subnetted with a /29 mask?

6 networks / 32 hosts
14 networks / 14 hosts
30 networks / 6 hosts
62 networks / 2 hosts

17. Which of the following devices extend a collision domain? (Choose two.)

switch
hub
bridge
router
repeater

18. What type of routing is it when the network administrator manually configures a route?

static
dynamic
interior
exterior

19. Which combination of network id and subnet mask correctly identifies all IP addresses from 172.16.128.0 through 172.16.159.255?

172.16.128.0 255.255.255.224
172.16.128.0 255.255.0.0
172.16.128.0 255.255.192.0
172.16.128.0 255.255.224.0
172.16.128.0 255.255.255.192

20. Which statement describes a star topology?

Each host in the network is connected to a backbone cable that is terminated at both ends.
Each host is connected to a hub or switch, either of which acts as a central point for all network connections.
Each host is directly connected to two other hosts to form a long chain of hosts.
Each host has a connection to all other hosts in the network.

21. A workstation is browsing a web server. What will be the partial contents of the segment sent from the workstation to the web server?

22. Which devices segment collision domains? (Choose two.)

transceiver
router
switch
hub
media

23. Refer to the exhibit. What is the order of the TCP/IP Protocol Data Units as data is moved as indicated through the OSI model?

data, segments, frames, packets, bits
data, packets, segments, frames, bits
data, segments, packets, frames, bits
data, packets, frames, segments, bits

24. A technician needs to connect a FastEthernet port from a router to a FastEthernet port on a switch. The graphic shows the RJ-45 cable ends for a patch cable. What result can be expected if this cable is used for the link?

The cable will be able to pass traffic between the devices.
The cable has reversed-pairs, which will degrade the signal quality.
The cable has split-pairs, which will increase crosstalk and create an unreliable link.
The cable has all the wires reversed, which will prevent the link lights from indicating that there is link.

25. Refer to the exhibit. What is the purpose of the highlighted address?

It allows the NIC to communicate with other devices on the same network. *
It identifies which part of the IP address is to be considered the network portion.
It provides an address to which all packets that do not have a specific route are sent.
It uniquely identifies the NIC to the free token that is passed on the Ethernet network.

26. Workstation A sends data to workstation B. What will have to be altered as the data passes through the router? (Choose two.)

Layer 1 bit pattern *
Layer 2 frames *
Layer 3 packets
Layer 4 segments
Layer 5 -7 data

27 Which type of address is 223.168.17.167/29?

host address
multicast address
broadcast address *
subnetwork address

28.Which subnet masks would be valid for a subnetted Class B address? (Choose two.)

255.0.0.0
255.254.0.0
255.224.0.0
255.255.0.0
255.255.252.0 *
255.255.255.192 *

29. Which cable diagram displays the end to end pinout for a console cable used with Cisco devices?

Cable A
Cable B
Cable C
Cable D

30. What should a network administrator consider when migrating to Gigabit Ethernet architecture from Fast Ethernet? (Choose three.)

Existing NICs might need to be upgraded.*
Existing switches might need to be upgraded. *
Existing NICs must support half-duplex mode.
Existing UTP wiring must be replaced with fiber.
Existing UTP must be tested for CAT 5e compatibility. *
Existing network topology must support shared media

31. A network user is using the FTP protocol to transfer data from the local host to an FTP server. The local host is also using the SNMP protocol to report the system status to the network management system. Which statement describes the communication from the host?

FTP and SNMP will use the same port number.
FTP uses TCP to establish a session before any data is transferred. *
The UDP session will reorder the SNMP data as it is received by the network management system.
The TCP protocol for the FTP transfer will use a random destination port number to the FTP server.

32. Refer to the exhibit. Which type of cabling should be used at each of the connection points shown?

A-crossover; B- straight-through; C-straight-through; D-fiber; E-straight-through
A-crossover; B-crossover; C-straight-through; D-fiber; E-crossover
A-straight-through; B-crossover; C-straight-through; D-fiber; E-straight-through
A-fiber; B-crossover; C-straight-through; D-crossover; E-straight-through
A-straight-through; B-crossover; C-crossover; D-fiber; E-straight-through
A-straight-through; B-crossover; C-straight-through; D-fiber; E-straight-through

33. How many broadcast domains are shown in the diagram?

three
four
five
six
seven
eight

34. Refer to the received frame in the exhibit. In what two ways is the information from the received frame used by a switch? (Choose two.)

192.168.10.5 is used to create an ARP request.
192.168.10.5 is used to build the forwarding table.
1234.5678.1abc is stripped from the frame header.
192.168.10.11 is left intact as the frame is forwarded.*
The switch compares 192.168.10.11 to the addresses in the routing table to make the forwarding decision.
To make the forwarding decision, the switch looks in its switch table for address* aaaa.bbbb.cccc.

35. Refer to the exhibit. What is an advantage of using this type of topology?

This type of network has redundancy.
No collisions occur on this type of network.
Network communication continues in the event of a break.
A central device on the network controls communication on this type of network.

36. Refer to the exhibit. An instructor in the network class has given the students the network diagram and asks the students to select the appropriate network devices. The goals are to provide a collision-free LAN environment and to provide Internet connectivity. What is the correct design?

Replace Box 1 with a hub and Box 2 with a router.
Replace Box 1 with a router and Box 2 with a bridge.
Replace Box 1 with a Layer 2 switch and Box 2 with a router.
Replace Box 1 with a router and Box 2 with a Layer 2 switch.
Replace Box 1 with a bridge and Box 2 with a Layer 2 switch.

37. Refer to the exhibit. A company needs to attach workstation E at a point 150 meters from an existing hub. What device should be placed at location D to allow the new host to connect to the network with the least amount of latency?

router
switch
bridge **
repeater**

38. Refer to the exhibit. Host A is being manually configured for connectivity to the LAN. Which two addressing scheme combinations are possible configurations that can be applied to the host for connectivity? (Choose two.)

Address - 192.168.1.14
Gateway - 192.168.1.33

Address - 192.168.1.45
Gateway - 192.168.1.33

Address - 192.168.1.32
Gateway - 192.168.1.33

Address - 192.168.1.82
Gateway - 192.168.1.65

Address - 192.168.1.63
Gateway - 192.168.1.65

Address - 192.168.1.70
Gateway - 192.168.1.65

39. What can be verified by successfully pinging the reserved loopback address on a host?

a. Connectivity exists between two hosts on the LAN.
b. The TCP/IP stack of the local host is installed correctly.
c. A connection exists between a host and the default gateway.
d. The route a packet takes from the local host to a remote host is valid.

40. Which layer of the OSI model defines the process of adding the source and destination IP address to a data packet?

transport
network *
data link
physical

41 Which protocols are TCP/IP application layer protocols? (Choose two.)

UDP
FTP*
IP
SMTP*
TCP

42. Refer to the exhibit. A network administrator is testing a connectivity issue in the network. The administrator discovers that host A cannot communicate with host B, host C, or RouterA. A ping command on host A to 127.0.0.1 succeeds. The NIC link indicator on host A is illuminated. Temporarily, the administrator removes the cable from host A and uses the LAN cable from host B to connect from host A to port 1 on the switch. While using the substitute cable, host A can communicate with host C and RouterA. At which layer of the OSI model was the problem occurring?

session
transport
network
data link
physical *

43. A collision has occurred on an Ethernet network. Which three statements explain the CSMA/CD process? (Choose three.)

After the jam signal, all transmission stops for a random period.*
When the collision is detected, the hosts stop transmission immediately.
When the collision is detected, the hosts stop transmission after eight microseconds.
When the backoff period expires, the hosts involved in the collision have priority to transmit.
When the backoff period expires, each host checks to see whether the networking media is idle and then attempts to transmit. *
When the collision is detected, the hosts continue to transmit using a jam pattern for a short time to ensure that all hosts detect the collision.*

44. What are three characteristics of the TCP protocol? (Choose three.)

exchanges datagrams unreliably
is used to send IP error messages
forces the retransmission of unacknowledged packets*
creates a virtual session between end-user applications*
carries the IP address of the destination host in the TCP header
is responsible for breaking messages into segments and reassembling them at their destination *

45. When the receiving workstation detects an error in the data it has received, it does not acknowledge receipt of the data. The source workstation retransmits the unacknowledged data. Which layer of the OSI model supports this process of retransmission?

network
application
session
transport*

46. When using Category 5 UTP cable, which RJ-45 pin pairs are used to exchange data between hosts on an Ethernet network?

1 and 2; 4 and 5
1 and 2; 3 and 6*
3 and 6; 7 and 8
4 and 5; 7 and 8

47. Refer to the exhibit. The internetwork in the exhibit has been assigned the IP address 172.20.0.0. What would be the appropriate subnet mask to maximize the number of networks available for future growth?

255.255.224.0
255.255.240.0
255.255.248.0
255.255.252.0
255.255.254.0
255.255.255.0

48. A user initiates three simultaneous FTP connections from the local host to the same FTP server. Which OSI layer is responsible for establishing and managing these different FTP connections?

application
session *
transport
network
data link

49. Which binary number is a representation of the decimal number 248?

11101000
11110100
11111000 *
11111010

50. Refer to the exhibit. Which type of UTP cable should be used to connect Switch1 to Switch2?

rollover
console
crossover*
straight-through

Text file Source (historic): geocities.com/dru5t/cisco/sem1

geocities.com/dru5t/cisco
geocities.com/dru5t

(to report bad content: archivehelp @ gmail)