Subject: Probleme mit VS1001g-Oszillator Newsgroups: de.sci.electronics Date: 2001-04-29 03:35:03 PST |
Mahlzeit, liebe Freunde, ich ärgere mich gerade schwarz über den OnChip-XTal-Oszillator des VS1001g. Die beiden im Datenblatt beschriebenen Beschaltungen wollen einfach nicht funktionieren. Und da habe ich extra noch eine Fernseherleiche für geschändet (10p, braun-schwarz-schwarz axial auf grünem Körper, Sony!), aber es geht einfach nicht. Mit Reihenwiderstand 330R und 10p schwingt er zwar, aber nicht richtig, nur am XTal2 ist da was zu sehen (ich führe das eher auf den etwas unsauberen Aufbau zurück) Noch nicht einmal nach dem Kochrezept aus der repairfaq (Dokument F_Ascii_Schem auf http://www.repairfaq.org/filipg/ ) funktioniert es. Mit einem HC04-Gatter hatte es in dieser Dimensionierung funktioniert. Mann, ich werd hier noch wahnsinnig... Gruß Henning -- henning paul online: http://www.oocities.org/hennichodernich/ everything you never wanted to know... PM: henningpaul@gmx.de , ICQ: 111044613
Subject: Re: Probleme mit VS1001g-Oszillator Newsgroups: de.sci.electronics Date: 2001-04-29 08:36:16 PST |
Henning, How do you know it doesn't swing ? Are you measuring or testing chip functionality ? I've never been able to _measure_ the actual swing of the oscillator, but the chip has always worked, when I send commands/mp3data to it. I've tried both setups from the original VLSI schematic. With a 24 MHz and a 15 MHz crystal using the clock doubler. No problem. /Jesper -- * * * Visit Jesper's AVR pages * * * http://www.myplace.nu/avr * * * * * * * * * * * * * * * * * * * * * * * "Henning Paul" <henningpaul@gmx.de> wrote in message news:qoqgc9.st1.ln@slowhand.paul.de... > Mahlzeit, liebe Freunde, > > ich ärgere mich gerade schwarz über den OnChip-XTal-Oszillator des VS1001g. > Die beiden im Datenblatt beschriebenen Beschaltungen wollen einfach nicht > funktionieren. Und da habe ich extra noch eine Fernseherleiche für > geschändet (10p, braun-schwarz-schwarz axial auf grünem Körper, Sony!), > aber es geht einfach nicht. Mit Reihenwiderstand 330R und 10p schwingt er > zwar, aber nicht richtig, nur am XTal2 ist da was zu sehen (ich führe das > eher auf den etwas unsauberen Aufbau zurück) Noch nicht einmal nach dem > Kochrezept aus der repairfaq (Dokument F_Ascii_Schem auf > http://www.repairfaq.org/filipg/ ) funktioniert es. Mit einem HC04-Gatter > hatte es in dieser Dimensionierung funktioniert. Mann, ich werd hier noch > wahnsinnig... > > Gruß > Henning > -- > henning paul online: http://www.oocities.org/hennichodernich/ > everything you never wanted to know... > PM: henningpaul@gmx.de , ICQ: 111044613 > >
Subject: Re: Probleme mit VS1001g-Oszillator Newsgroups: de.sci.electronics Date: 2001-04-29 09:29:23 PST |
Jesper Hansen wrote: > Henning, > > How do you know it doesn't swing ? > Are you measuring or testing chip functionality ? > I've never been able to _measure_ the actual swing of the oscillator, > but the chip has always worked, when I send commands/mp3data to it. > > I've tried both setups from the original VLSI schematic. With a 24 MHz > and a 15 MHz crystal using the clock doubler. I have used my 10MHz Scope, but only High-Levels on XTAL1 and XTAL2. My first prototype used a dedicated Oscillator, using an HC04, so I have no comparison. My new prototype isn't that far to be tested by sending commands. But checking DREQ might be worth a try... cu Henning -- henning paul online: http://www.oocities.org/hennichodernich/ everything you never wanted to know... PM: henningpaul@gmx.de , ICQ: 111044613
Subject: Re: Probleme mit VS1001g-Oszillator Newsgroups: de.sci.electronics Date: 2001-04-29 10:25:13 PST |
"Henning Paul" <henningpaul@gmx.de> wrote in message news:bjfhc9.6k1.ln@slowhand.paul.de... > > I have used my 10MHz Scope, but only High-Levels on XTAL1 and XTAL2. My > first prototype used a dedicated Oscillator, using an HC04, so I have no > comparison. My new prototype isn't that far to be tested by sending > commands. But checking DREQ might be worth a try... You should do that. It seems to be impossible to measure with a 'scope. I've tried several expensive probes/scopes. > cu > Henning > -- > henning paul online: http://www.oocities.org/hennichodernich/ > everything you never wanted to know... > PM: henningpaul@gmx.de , ICQ: 111044613 > /Jesper -- * * * Visit Jesper's AVR pages * * * http://www.myplace.nu/avr * * * * * * * * * * * * * * * * * * * * * * *
Subject: Re: Probleme mit VS1001g-Oszillator Newsgroups: de.sci.electronics Date: 2001-04-29 11:06:03 PST |
On Sun, 29 Apr 2001 17:24:09 GMT, "Jesper Hansen" <jesperh@telia.com> wrote: >You should do that. It seems to be impossible to measure with a 'scope. I've >tried I tried with mine Tek7904, and I can see a nice sinuswave, going from 0 to near Supply-Voltage. Cu, Jan
Subject: Re: Probleme mit VS1001g-Oszillator Newsgroups: de.sci.electronics Date: 2001-04-29 11:08:53 PST |
Jesper Hansen wrote: > > I have used my 10MHz Scope, but only High-Levels on XTAL1 and XTAL2. My > > first prototype used a dedicated Oscillator, using an HC04, so I have no > > comparison. My new prototype isn't that far to be tested by sending > > commands. But checking DREQ might be worth a try... > > You should do that. It seems to be impossible to measure with a 'scope. > I've tried > several expensive probes/scopes. Thank You, Jesper! That was the problem. DREQ goes high, so the VS1001 must be alive. I have just finished building the first level of Erik Hermann's MP3-playing dongle draft, using a PISO shifting register and an AT90S2313. SUB-D connector and shifting register are still missing. Software is next, On/Off-Test, sine wave etc. Then I will complete the project. (And hopefully, by then Erik will have published circuit and especially software, I'm a not-so-talented programmer :-) cu Henning -- henning paul online: http://www.oocities.org/hennichodernich/ everything you never wanted to know... PM: henningpaul@gmx.de , ICQ: 111044613