International Harvester & McCormick Deering  

IHC 1hp Mogul Main Bearings

 $75 a set - plus $6.00 S&H

IHC Mogul Needle Valve

IHC Mogul 1, 1 3/4 and 2 1/2 hp push rod engines

Mogul needle valve  ---  $22.95 ea.

IHC Mogul Push Rod #1420T

(Fuel Pump)

IHC Mogul Fuel Pump Push Rod (IHC #1420T) fits - IHC Mogul 1, 1 3/4 and 2 1/2 hp engines.

IHC Mogul Push Rod ---  $23.95 ea.

IHC Mogul Accurate Engine  & Tractor

Magneto Trips, Pins & Rollers

The Accurate magneto trip used on IHC Mogul tractors are made from 7/16" square 4140 steel stock. The thread is 3/8" x 24NF. Each trip is supplied with a 3/8"x24 NF Nut.

Below I've pictured the replacement pins, rollers and retaining clips made like the originals for the Accurate type "O" magneto. The Accurate magneto is commonly found on IHC Mogul engines. These 5/16" diameter pins and spring rollers are made from 4140 steel and oil hardened for long wear.

Spring roller, pins and retaining clips 

(shown above with an Accurate Magneto trip finger and a Webster side plate))

Accurate Trip finger for Mogul engines -- $115 ea.

Tractor Trip Finger (top photo) ---  $8.95 ea.

Accurate Type "O" or Webster Magneto Spring Roller 5/16" or 3/8" bore --- $3.00 ea.

Accurate Type "O" Spring Button Head Roller Pins 5/16" OD  --- $5 ea.

Retaining Clips for 5/16" or 3/8" diameter pins --  10 for $3.50

Complete Accurate Type"O" Roller Pin assembly (pin,roller & clip) ---- $6.95 ea. 

IHC Famous 3hp Vert. Wrist Pin

Replacement Wrist Pin for 3hp vertical Famous 

$39.95 ea.

IHC Famous 3hp Vert. Needle Valve

Reproduction Needle Valves for IHC Famous 3hp Vert. engine. Machined needle valves pinned like the original. Needle valve measures 2 15/16" long, threaded 1/4 x 20 NC, knob is brass and 1 1/2" diameter.

$26.00 ea.

IHC Titan Needle Valve

IHC Titan engines. These are machined needle valves pinned like the original. Needle valve measures  threaded 1/4 x 20 NC, knob is 1" diameter fit 4 & 6hp engines.

$24 ea.

Order Parts Special & Save

1 Pair - gas and kerosene needle valve - $44.00 pr.  

IHC Famous & Titan Fuel Pump Plungers

All brass pump plunger 3/4" diameter fits IHC pumps. Other diameters and lengths made upon request.

Brass -- $18.50 ea.

Steel -- $17.00 ea.

IHC 2 1/2HP Famous Fuel Pump Plunger

4 3/8" long -- $14.95 ea.

IHC Needle Valves

IHC needle valves - brass knob 3/8" NC thread

$25 ea. 

IHC Mixer Covers     

IHC Mixer Cover #G1014 - for Farm Junior through 6 hp engines

IHC Mixer Cover #G183 - for engines from 4 to 25 hp

Covers ID machined

G1014 - $16 ea. ~~~~~  G183 $18 ea.

Send mail to ottosideshaft@yahoo.com with questions or comments about this web site. 

This site was last modified on 07/29/2008