If you have any experiences, facts, hints comments or data that you think might be useful on the site, please
and I will post it, with an acknowledgement of your contribution (if you so wish).
Notes taken by Jack L. Poller
Notes not presented in any particular order
In an automobile engine, the piston speed (RPM) and therefore piston tempature changes greatly and quickly. The tempature differences allow the ash to break up into small deposits, and go into the exhaust or blow by the rings into the crankcase and lubricants.
In an airplane engine, the pistons are operating continuously at a single speed, and therefore do not go through heating and cooling cycles, so the ash deposits would not break up.
Generally, for automobile motor, lubricant is limited to 1% ash content. 2% ash is asking for trouble (although 2% may be okay for a diesel engine). Red Line Racing Oils are low detergent. Detergent is left out because ash can cause detonation.
Average oil filter is a 20 micron filter. Could go down to 1 micron. Stuff that dispersant holds in suspension is much less than microns (it is measured at the molecular level, in Angstroms). At proper temperature, the stuff is not really a problem. Most of the stuff is Aromatic Hydrocarbons, boil around 180 F, and leave through crankcase ventilation.
The surface gets plated with either Iron Phosphate or Iron Sulfate, both of which are softer than the base Iron. This chemical reaction occurs in the 300 to 400 F range, and the Zinc is a temperature controlling carrier (controls the temperature at which the reaction occurs. When the two metal surfaces come in contact, a small amount of the surface plating is 'scraped' off of the surface. This is replenished by more ZDP contact with the metal. This action prevents the metals welding through heat generated by high friction contact. The ZDP in the lubricant may last up to 20,000 miles.
Key Advantages:
Red Line has 1/2 Cf of Mobil 1.
Viscosity vs. Sheer strength are similar, but Red Line handles high loads better.
Can gain 1 - 2% more power by going to a lower viscosity oil.
There is no longer a problem with synthetic lubricants eating away seals. (Original Mobil-1, no longer available, left out seal-swell).
Red Line blends its lubricants, but does not manufacture the synthetic bases.
Start with a base of straight weight Oil. Then add a polymeric thickener. When hot, the long polymer chain is really moving around, causing the oil to flow less. When cold, the polymers stick to each other, essentially comming out of suspension. The polymers are stable up to about 210 F, where they start to break up. The drawbacks to VI polymers is that they can cause engine dirt because of their low shear strength.
Viscosity A B C D High | ' ' ' ' | ' ' ' ' |* ' ' ' ' | \ ' ' ' ' | *- ' ' ' ' | *\ ' ' ' ' | *- ' ' ' ' | *\' ' ' ' | *- ' ' ' | ' *\ ' ' ' |-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+- | ' *-*\ ' ' ' | ' *\*-*\*-*\*-*\*-*\*-*\*-*\*-*\*-*\ | ' ' ' ' Low |_____________________________________________________________ Low High Sheer Rate A Shear at Piston Rings B Shear at Main Bearings C Shear at Cylinder Wall D Shear at Connecting Rod Bearings -+-+ Viscosity of a Straight Weight Oil (Petro. Or Synthetic) *\*- Viscosity of A MultiGrade Oil (Base with VI polymers)What this chart shows is that a straight oil has the same viscosity regardless of shear rate. However, as the shear rate increases, the shear breaks down the VI polymers, and multigrade oils have less actual viscosity at the localized high shear rate area.
The weak link is the rod bearings and Cam, in terms of rate of shear. There is less friction at the piston rings. Anti Wear is much more important at the cam.
700 ------------------------------------------------------------- | 600 Maximum Useful Range of All Proof Synthetic Motor Oil | | 500 ------------------------------------------------ | --------------------------------- Maximum | | 400 ----------------| | Useful | | Maximum Useful | Maximum | Range of | | 300 Range of | Useful | Diester | | Premium | Range of | Synthetic | | 200 Petroleum | Polyolefins | Motor Oils | | Motor Oils | | | | 100 | | | | | | | | 0_______________________|_______________|_______________|___________|
Upper Cylinder Wall 300 - 500 Exhaust Valve 1200 - 1500 Piston Crown 700 - 800 Hydraulic Valve Lifter 250 - 300 Crankcase 200 - 300 Top Ring 300 - 650 Exhaust Gases 500 - 1000 Combustion Chamber 3000 - 5000 Coolant Jacket 165 - 230 Connecting Rod Bearings 200 - 375 Main Bearings 200 - 350
Water Wetter has a high Ph, but also has silicates, so it can be used in aluminium radiators. However, if left for a long time, the silicates are depleted, and damage will occur. The liquid versions of Water Wetter do not have phosphates.
Discovered by Roy Howell. Some engineers were begging Roy to develop a corrosion inhibitor to add to straight water for racers, since racers rarely use AntiFreeze. He did some work, developed Water Wetter simply as a corrosion inhibitor, and gave it to Huffaker. Huffaker immediately noticed lower operating temperatures, and Roy started to investigate why.
You *can* cool an engine too much. The ideal temperature for coolant is 190 F.
AntiFreeze has 1/4 heat transfer capability of straight water.
Temperature recordings at block water jacket exit, after stabilizing:
Water Anti-Freeze Water Wetter Temperature (F) 50% 50% No 228 50% 50% Yes 220 100% 0% No 220 100% 0% Yes 202
Dexron - GM - less Cf than Type F
Now Mercon and Dexron II are almost identical.
Gear oil is acidic, motor oil is alkiline. Gear oil needs very high wear protection - Extreme Pressure (marked as EP). Therefore, it has a very high sulfer and phospor content. Sulfur and Phosphate reactions start at a lower temperature, and Gear Oil has much more additive than motor oil. This additive is corrosive to copper bearings and bronze synchro rings.
Positraction additives are Friction modifiers - make the base oil much more slippery. They coat the metal surfaces, and prevent the stick/slip mode of operation, preventing shudder, and causes smoother take-up. Friction Modifiers may detract from EP characteristics.
Friction modifiers cause smooth take-up of Limited slip units. For track racing, FM is probably undesireable, and immediate take-up is more important. For Street, FM is usually reccomended for more comfortable operation.
Gear oils decompose at lower temperature, usually 250 F.
Gear Lubrication Ratings
GL-1 No Additives GL-2 GL-3 GL-4 Suitable for light duty hypoid sets GL-5 Has lots of sulfer - Heavy duty hypoids GL-6Hypoid type gear sets have a sliding rather than rolling action, and therefore require much greater wear protection.
GL-5 Should be used in rear differentials.
GL-6 is a heavier weight GL-5. Used for heavy trucks and Tow Vehicles.
Red Line 75 - 90 NS has No Slip, i.e., no Friction Modifiers.
Red Line 75 - 90 has Friction Modifiers.
Gear mesh in Gears litterally chops up and cuts apart the long polymer chains of Viscosity Index improvers.
Smell of gear oil is from high sulfur content.
Quaiff Differential is a worm gear, and needs a very slippery oil.
STP is a VI.
Castrol R is Castor Oil based. Good lubrication, but dirty.
Methyl Lead goes to intake faster than Ethyl Lead. EPA now has authority to outlaw lead entirely.
Marvel Mystery Oil and Rislone are surfactants and penetrants.
Neo and other Zero Weight oils are actually 0W - 20 multigrade oils, so as soon as they warm up, they are effectively 20 weight oil.
Should not use silicone (DOT-5) brake fluid in ABS systems, as there is little to no lubrication for ABS pump.
Red Line recommends breaking in an engine on straight viscosity oil.
Red Line does not recommend mixing race oil with regular oil.
Can use Race Oil for 3 to 4 Events.
Jack L. Poller
Novell, Inc., 2180 Fortune Dr., San Jose, CA 95131
jpoller@novell.com
(408) 473-8252
If you have any experiences, facts, hints comments or data that you think might be useful on the site, please
and I will post it, with an acknowledgement of your contribution (if you so wish).