PrincessJewelry

~*Princess Jewelry*~

~*Princess Diamond Necklace*~

~*Princess Necklace*~

~*Make a Princess Tiara*~



				~Princess Necklace~ Materials used: 19 Headpins (#50100) Qty: 1 Spring Clasp (#50142) Qty: 3 Jump Rings (#50040) Qty: 101 4mm AB Clear Faceted Crystal Rounds (#16171-F) Qty: (abbreviated CR in these instructions) 333 Clear AB Seed Beads (#J-721) Qty: 2 Crimp Beads (#50046) Qty: 22” Tiger Tail Beading Wire (#49013) Qty: Directions: To begin, make 19 “dangles” as follows. Keep them in order as you make them. Put on headpins, form small loop at the top, cut off excess. Middle, make 1: CR, 7 seed beads, CR, 7 seed beads, CR, 7 seed beads. 2 each: CR, 6 seed beads, CR, 6 seed beads, CR, 6 seed beads. 2 each: CR, 6 seed beads, CR, 6 seed beads, CR, 5 seed beads. 2 each: CR, 6 seed beads, CR, 5 seed beads, CR, 5 seed beads. 2 each: CR, 5 seed beads, CR, 5 seed beads, CR, 5 seed beads. 2 each: CR, 5 seed beads, CR, 5 seed beads, CR, 4 seed beads. 2 each: CR, 5 seed beads, CR, 4 seed beads, CR, 4 seed beads. 2 each: CR, 4 seed beads, CR, 4 seed beads, CR, 4 seed beads. 2 each: CR, 4 seed beads. CR, 4 seed beads. CR, 3 seed beads. 2 each: CR, 4 seed beads, CR, 3 seed beads, CR, 3 seed beads. Lay out the dangles in order. Begin stringing the necklace as follows: Crimp bead, jump ring, wire back through crimp bead. Close the crimp bead. Leave about 1” wire. Thread: 1 CR, 7 seed beads; do this 12 times. End with CR. Add dangle, CR, dangle, CR, until all 19 dangles are in place. Then: 1 CR, 7 seed beads; do this 12 times. End with CR. String crimp bead, spring clasp, and back through the crimp bead. Close the crimp bead. Trim off tail. Your necklace is complete! You will look as good as Cinderella at the Ball!!
	~Princess Diamond Necklace~ Materials: 1 pkg rocaille crystal beads (8 grams) 1 pkg 4 mm crystal cut beads 1 pkg 8 mm crystal cut beads 3 head pins 21 inches of fishline or invisible jewelry wire (longer or shorter to fit) Clasp of choice 2 crimping beads Round nosed pliers Needle nose pliers Aileene's Tacky Glue First, prepare the crystal drops. Take a head pin jewelry wire and thread one 4 mm bead followed by one 8 mm bead. Use the pliers to cut the excess wire, leaving enough to curl into a loop. Using the round head pliers, bend the wire into a loop. Use the needle nose pliers to squeeze the loop into place if necessary. Repeat this process two more times. Next, thread a crimp bead on the fishline and loop the line through the loop in one side of the clasp. Thread the end of the wire back through the crimp bead. Apply pressure to the crimp bead until it is holding both pieces of the fishline securely. Add a drop of Aileen's Tacky Glue to the crimp bead to ensure that it won't slip. When the glue has dried, you can begin the beading. I will call the rocaille beads small, 4mm will be medium and 8mm will be large. Thread 20 small beads. Follow with this combo: one medium, five small, the drop you made earlier, five small, one medium, five small, another drop, five small, one medium, five small, the last drop, five small, and one medium. Finish it off with 20 more small beads. Thread the line through the other crimp bead and then through the other half of the clasp. Go back through the crimp bead and squeeze the bead with the needle nose pliers. Add a drop of glue to the crimp bead and let it dry*~


		~Make a Princess Tiara~ What You Need: 4 12" Metallic Pipe Cleaners 12 Red Translucent Pony Beads 20 Pink Translucent Pony Beads 44 Chrystal Faceted 8mm Beads Instructions: Twist the ends of two stems together to make one 23" (approx.) stem that will fit around the princess' head. Slide 20 pink and 5 red pony beads to the center of the 23" stem according to pattern at right. Gently bend stem. Slide a 3rd 12" stem through the middle red bead and center it. One one side, add 3 faceted beads, 1 red pony bead and 3 more faceted beads. Slide that end of the stem through the next red pony bead. Repeat, finishing that side by sliding under the last red pony bead. Repeat for other side. Twist ends to secure beads. Slide 9 beads (4 faceted, 1 red pony bead, 4 faceted) to the center of the last 12" stem. Bend gently. Push each end through one of the red pony beads on the top middle of the tiara. Add 7 beads to each side (3 faceted, 1 red pony bead, 3 faceted) and push ends through the remaining red pony beads. Twist to secure. Trim ends, then wear it Like a Princess*~