|
||
|
1-Router
kutusu içinde çıkan konsol kablosunun ilgili ucu routerin konsol
portuna,diğer ucunu PC’nizin comm.(seri 1-2) portuna takınız.WinNT
‘deki Hyperterminal programını kullanarak
routerun yazılımına erişilebilir.Haberleşme hızını (Bits per
second) 9600 Baundda ayarlayınız. 2-Routera baglanıldığında; Router Quick Configuration for the
following: o
Interfaces o
Bridging
Spanning Tree Bridge
(STB) o
Protocols
IP (including OSPF,
RIP and SNMP)
IPX
DNA (DECnet) o
Booting Event Logging will be enabled for
all configured subsystems with logging level 'Standard' ********************************************************** Interface Configuration ********************************************************** Type 'Yes' to Configure Interfaces Type 'No' to skip Interface
Configuration Type 'Quit' to exit Quick Config Configure Interfaces? (Yes, No,
Quit): [Yes] seçeneğini seçiniz. 3- Intf 0 is Ethernet Intf 1 is WAN PPP Encapsulation for WAN 1
(Proteon Serial, PPP, Frame Relay): [PPP] Intf 2 is WAN PPP Encapsulation for WAN 2
(Proteon Serial, PPP, Frame Relay): [PPP] This is all configured device
information: Intf 0 is Ethernet, Connector
(10baseT, BNC) auto-configured Intf 1 is WAN 1 with PPP
Encapsulation, Intf 2 is WAN 2 with PPP
Encapsulation, Save this configuration? (Yes, No):
[Yes] seçeneklerini seçiniz. 4- Bridging Configuration ********************************************************** Type 'Yes' to Configure Bridging Type 'No' to skip Bridging
Configuration Type 'Quit' to exit Quick Config Configure Bridging? (Yes, No, Quit):
[Yes] n Bridge seçeneğini seçmeyiniz. 5- ********************************************************** Protocol Configuration ********************************************************** Type 'Yes' to Configure Protocols Type 'No' to skip Protocol
Configuration Type 'Quit' to exit Quick Config Configure Protocols? (Yes, No,
Quit): [Yes] Type 'r' any time at this level to
restart Protocol Configuration Configure IP? (Yes, No): [Yes] Type 'r' any time at this level to
restart IP Configuration IP Configuration is already present Configure IP anyway? (Yes, No): [No]
y Configuring Per-Interface IP
Information Configuring Interface 0 (Ethernet) Configure IP on this interface?
(Yes, No): [Yes] IP Address: Yukarıdaki seçenekleri seçerek,şubenin ethernet IP adresini ve subnet mask adresini giriniz. 5- Configuring Interface 1 (Ethernet) Configure IP on this interface?
(Yes, No): [Yes] IP Address: [] Seçeneğini kullanarak WAN adresini ve subnet mask adresini giriniz.Kullanmadığınız interface’leri seçmeyiniz. 6- Configuring IP Routing Information Enable Dynamic Routing? (Yes, No):
[Yes] Enable OSPF? (Yes, No): [Yes] OSPF Enabled with Max routes = 1000
and Max routers = 50 Routing Configuration Complete SNMP will be configured with the
following parameters:
Community: public
Access:
READ-ONLY This is the information you have
entered:
Interface #
IP Address Address Mask
0
33.33.33.33 33.33.33.33
1
99.99.99.99 255.0.0.0 OSPF is configured, and RIP is
configured only for 'sending' Save this configuration? (Yes, No):
[Yes] Dynamic Routing ve Enable OSPF seçeneklerini
seçerek kaydediniz. 7- Configure IPX? (Yes, No): [Yes] n Configure DNA? (Yes, No): [Yes] n ********************************************************** Booting Configuration ********************************************************** Type 'Yes' to Configure Booting Type 'No' to skip Booting
Configuration Type 'Quit' to exit Quick Config Configure Booting? (Yes, No, Quit):
[Yes] n ********************************************************** OBM
Configuration ********************************************************** Type 'Yes' to Configure OBM Type 'No' to skip OBM Configuration Type 'Quit' to exit Quick Config Configure OBM? (Yes, No, Quit):
[Yes] n Quick Config Done Type RESTART at the '*' prompt for
the configuration to take effect Config> Yukarıdaki seçenekleri seçerek
Ctrl-P tuşlarına basarak haberleşme promptuma düşünüz. * RESTART komutu kullanarak konfigürasyon işlemini tamamlayınız. |