_________ _________
_| \__/ |_
<--> P24 |_|1 18|_| P23 <-->
_| |_
<--> P25 |_|2 17|_| P22 <-->
_| |_
<--> P26 |_|3 16|_| P21 <-->
_| Z86E04 |_
<--> P27 |_|4 Z86E08 15|_| P20 <-->
_| |_
VCC |_|5 14|_| GND
_| |_
<-- XTAL2 |_|6 13|_| P02 <-->
_| |_
--> XTAL1 |_|7 12|_| P01 <-->
_| |_
--> P31 |_|8 11|_| P00 <-->
_| |_
--> P32 |_|9 10|_| P33 <--
|______________________|
Z8 CPU Z86E30/E31 Pin Description:
_________ _________
_| \__/ |_
<--> P25 |_|1 28|_| P24 <-->
_| |_
<--> P26 |_|2 27|_| P23 <-->
_| |_
<--> P27 |_|3 EPROM/OTP: 26|_| P22 <-->
_| Z86E30 |_
<--> P04 |_|4 Z86E31 25|_| P21 <-->
_| MASK: |_
<--> P05 |_|5 Z86C30 24|_| P20 <-->
_| Z86C31 |_
<--> P06 |_|6 23|_| P03 <-->
_| |_
<--> P07 |_|7 22|_| GND
_| |_
+5V VCC |_|8 21|_| P02 <-->
_| |_
<-- XTAL2 |_|9 20|_| P01 <-->
_| |_
--> XTAL1 |_|10 19|_| P00 <-->
_| |_
--> P31 |_|11 18|_| P30 <--
_| |_
--> P32 |_|12 17|_| P36 -->
_| |_
--> P33 |_|13 16|_| P37 -->
_| |_
<-- P34 |_|14 15|_| P35 -->
|______________________|
Z80 CPU Pin Description:
_________ _________
_| \__/ |_
<-- A11 |_|1 40|_| A10 -->
_| |_
<-- A12 |_|2 39|_| A9 -->
_| |_
<-- A13 |_|3 Z80 CPU 38|_| A8 -->
_| |_
<-- A14 |_|4 37|_| A7 -->
_| |_
<-- A15 |_|5 36|_| A6 -->
_| |_
--> CLK |_|6 35|_| A5 -->
_| |_
<--> D4 |_|7 34|_| A4 -->
_| |_
<--> D3 |_|8 33|_| A3 -->
_| |_
<--> D5 |_|9 32|_| A2 -->
_| |_
<--> D6 |_|10 31|_| A1 -->
_| |_
VCC |_|11 30|_| A0 -->
_| |_
<--> D2 |_|12 29|_| GND
_| |_
<--> D7 |_|13 28|_| /RFSH -->
_| |_
<--> D0 |_|14 27|_| /M1 -->
_| |_
<--> D1 |_|15 26|_| /RESET <--
_| |_
--> /INT |_|16 25|_| /BUSRQ <--
_| |_
--> /NMI |_|17 24|_| /WAIT <--
_| |_
<-- /HALT |_|18 23|_| /BUSAK -->
_| |_
<-- /MREQ |_|19 22|_| /WR -->
_| |_
<-- /IORQ |_|20 21|_| /RD -->
|______________________|
Z80 CPU SMD and QFP Pin Description:
A lot of people have been requesting the Z80 pinouts. Well, here they are,
directly from the Zilog Z80 Microprocessor Family Databook.
44 pin QFP:
1 - CLK 2 - D4 3 - D3 4 - D5 5 - D6
6 - +5V 7 - D2 8 - D7 9 - D0 10 - D1
11 - NC 12 - ~INT 13 - ~NMI 14 - ~HALT 15 - ~MREQ
16 - ~IORQ 17 - NC 18 - ~RD 19 - ~WR 20 - ~BUSACK
21 - ~WAIT 22 - ~BUSREQ 23 - ~RESET 24 - ~M1 25 - ~RFSH
26 - GND 27 - A0 28 - A1 29 - A2 30 - A3
31 - A4 32 - A5 33 - NC 34 - A6 35 - A7
36 - A8 37 - A9 38 - A10 39 - NC 40 - A11
41 - A12 42 - A13 43 - A14 44 - A15
The "~" stands for "not" ( i.e. active low ). The pins are counted
counter-clockwise, pin 1 starting from the bevel ( or the corner dot ).
This may be different on the Toshiba chip used in the TI so I assume no
responsibility for anyone frying their calc.
Z80 PIO Pin Description:
_________ _________
_| \__/ |_
<--> D2 |_|1 40|_| D3 <-->
_| |_
<--> D7 |_|2 39|_| D4 <-->
_| |_
<--> D6 |_|3 Z80 PIO 38|_| D5 <-->
_| |_
--> /CE |_|4 37|_| /M1 <--
_| |_
--> C/D |_|5 36|_| /IORQ <--
_| |_
--> B/A |_|6 35|_| /RD <--
_| |_
<--> PA7 |_|7 34|_| PB7 <-->
_| |_
<--> PA6 |_|8 33|_| PB6 <-->
_| |_
<--> PA5 |_|9 32|_| PB5 <-->
_| |_
<--> PA4 |_|10 31|_| PB4 <-->
_| |_
GND |_|11 30|_| PB3 <-->
_| |_
<--> PA3 |_|12 29|_| PB2 <-->
_| |_
<--> PA2 |_|13 28|_| PB1 <-->
_| |_
<--> PA1 |_|14 27|_| PB0 <-->
_| |_
<--> PA0 |_|15 26|_| VCC +5V
_| |_
--> /AOE |_|16 25|_| CLOCK <--
_| |_
--> /BOE |_|17 24|_| INT ENABLE IN <--
_| |_
<-- AREADY |_|18 23|_| /INT -->
_| |_
<-- D0 |_|19 22|_| INT ENABLE OUT -->
_| |_
<-- D1 |_|20 21|_| BREADY -->
|______________________|
C/D CONTROL=1, DATA=0
B/A PORT B=1, PORT A=0
8255 PIO Pin Description:
_________ _________
_| \__/ |_
<--> PA3 |_|1 40|_| PA4 <-->
_| |_
<--> PA2 |_|2 39|_| PA5 <-->
_| |_
<--> PA1 |_|3 8255 38|_| PA6 <-->
_| 82C55 |_
<--> PA0 |_|4 37|_| PA7 <-->
_| |_
--> /RD |_|5 36|_| /WR <-- (*NOTE)
_| |_
--> /CS |_|6 35|_| RES <-- ACTIVE HI
_| |_
GND |_|7 34|_| D0 <-->
_| |_
--> A1 |_|8 33|_| D1 <-->
_| |_
--> A0 |_|9 32|_| D2 <-->
_| |_
<--> PC7 |_|10 31|_| D3 <-->
_| |_
<--> PC6 |_|11 30|_| D4 <-->
_| |_
<--> PC5 |_|12 29|_| D5 <-->
_| |_
<--> PC4 |_|13 28|_| D6 <-->
_| |_
<--> PC0 |_|14 27|_| D7 <-->
_| |_
<--> PC1 |_|15 26|_| VCC
_| |_
<--> PC2 |_|16 25|_| PB7 <-->
_| |_
<--> PC3 |_|17 24|_| PB6 <-->
_| |_
<--> PB0 |_|18 23|_| PB5 <-->
_| |_
<--> PB1 |_|19 22|_| PB4 <-->
_| |_
<--> PB2 |_|20 21|_| PB3 <-->
|______________________|
(*note) If you use the CMOS version (82C55) then delay the /WR signal
so it's active AFTER chipselect, you can use this:
82C55 |_ ___
PIN 36|_| ------*---|___|---- /WR from the CPU (Z80)
| | R1
| Use thise values:
--- -----------------
--- C1 CPU 4 MHz 8MHz
| C1 47p 33p
| R1 470E 330E
GND
This is something I have found out myself, after looking the timing over
the 82C55, 8255 and the Z80..
16C550, 16C450, 8250 UART Pin Description:
_________ _________
_| \__/ |_
<--> D0 |_|1 40|_| VCC +5V
_| |_
<--> D1 |_|2 39|_| /RI <--
_| |_
<--> D2 |_|3 16C550 38|_| /CD <--
_| 16C450 |_
<--> D3 |_|4 8250 37|_| /DSR <--
_| serial |_
<--> D4 |_|5 interface 36|_| /CTS <--
_| |_
<--> D5 |_|6 35|_| RESET <--
_| |_
<--> D6 |_|7 34|_| /OP1 -->
_| |_
<--> D7 |_|8 33|_| /DTR -->
_| |_
--> RCLK |_|9 32|_| /RTS -->
_| |_
--> RX |_|10 31|_| /OP2 -->
_| |_
<-- TX |_|11 30|_| INT -->
_| |_
--> CS0 |_|12 29|_| /RXRDY -->
_| |_
--> CS1 |_|13 28|_| A0 <--
_| |_
--> /CS2 |_|14 27|_| A1 <--
_| |_
<-- BOUT |_|15 26|_| A2 <--
_| |_
--> XTAL1|_|16 25|_| /AS <--
_| |_
<-- XTAL2|_|17 24|_| /TXRDY -->
_| |_
--> /WR |_|18 23|_| /DIS -->
_| |_
--> WR |_|19 22|_| RD <--
_| |_
GND |_|20 21|_| /RD <--
|______________________|
D0-D7 Data bus in/out.
RCLK Recieve Clock Input. (normaly connected to BOUT)
RX Serial Data Input (mark=high=1 and space=low=0)
TX Serial Data Output.
CS0 Chip Select 0 input (Active high)
CS1 Chip Select 1 input (Active high)
CS2 Chip Select 2 input (Active low) (CS0=1 and CS1=1 and CS2=0 will enable data transfer)
BOUT Baud rate generator clock output (16*baudrate)
XTAL1 Crystal input 1 or external clock input.
XTAL2 Crystal input 2 or buffered clock output.
/WR Write strobe (active low)
WR Write strobe (active high)
GND Signal and power ground.
/RD Read strobe (active low)
RD Read strobe (active high)
/DDIS Drive disable output (active low)
/TXRDY Transmit ready output (active low) goes low when TX-FIFO is full
/AS Address strobe input (active low) if not used tie low.
A2 Address select line 2 input, to select internal registers.
A1 Address select line 1 input, to select internal registers.
A0 Address select line 0 input, to select internal registers.
/RXRDY Recieve ready output (active low) goes low when RX-FIFO is full
INT Interrupt output (active high) this pin can be programmed to go high on conditions.
/OP2 General purpose output2 (active low)
/RTS Request to send output (active low)
/DTR Data terminal ready output (active low)
/OP1 General purpose output1 (active low)
RESET Master reset input (active high)
/CTS Clear to send input (active low)
/DSR Data set ready input (active low)
/CD Carrier detect input (active low)
/RI Ring detect indicator input (active low)
VCC Power supply input +5Volt.
27C256 EPROM Pin Description:
_________ _________
_| \__/ |_
(*Note) VPP |_|1 28|_| VCC +5V
_| |_
--> A12 |_|2 27|_| A14 <--
_| |_
--> A7 |_|3 27C256 26|_| A13 <--
_| EPROM |_
--> A6 |_|4 25|_| A8 <--
_| |_
--> A5 |_|5 24|_| A9 <--
_| |_
--> A4 |_|6 23|_| A11 <--
_| |_
--> A3 |_|7 22|_| /OE <--
_| |_
--> A2 |_|8 21|_| A10 <--
_| |_
--> A1 |_|9 20|_| /CE <--
_| |_
--> A0 |_|10 19|_| D7 -->
_| |_
<-- D0 |_|11 a 18|_| D6 -->
_| |_
<-- D1 |_|12 17|_| D5 -->
_| |_
<-- D2 |_|13 16|_| D4 -->
_| |_
GND |_|14 15|_| D3 -->
|______________________|
(*Note) VPP shuld be high, on some EPROMs the output is disabled when VPP=low, tie it high always.
84256 RAM Pin Description:
_________ _________
_| \__/ |_
--> A14 |_|1 28|_| VCC +5V
_| |_
--> A12 |_|2 27|_| /WE <--
_| |_
--> A7 |_|3 84256 26|_| A13 <--
_| RAM |_
--> A6 |_|4 25|_| A8 <--
_| 32 KBytes |_
--> A5 |_|5 24|_| A9 <--
_| |_
--> A4 |_|6 23|_| A11 <--
_| |_
--> A3 |_|7 22|_| /OE <--
_| |_
--> A2 |_|8 21|_| A10 <--
_| |_
--> A1 |_|9 20|_| /CE <--
_| |_
--> A0 |_|10 19|_| D7 <-->
_| |_
<--> D0 |_|11 18|_| D6 <-->
_| |_
<--> D1 |_|12 17|_| D5 <-->
_| |_
<--> D2 |_|13 16|_| D4 <-->
_| |_
GND |_|14 15|_| D3 <-->
|______________________|
8416 RAM Pin Description:
_________ _________
_| \__/ |_
--> A7 |_|1 24|_| VCC +5V
_| yPD446 |_
--> A6 |_|2 TC5517 23|_| A8 <--
_| HM6116 |_
--> A5 |_|3 MB8416 22|_| A9 <--
_| RAM |_
--> A4 |_|4 21|_| /WE <--
_| 16384 Bit |_
--> A3 |_|5 2048 Bytes 20|_| /OE <--
_| |_
--> A2 |_|6 19|_| A10 <--
_| |_
--> A1 |_|7 18|_| /CE <--
_| |_
--> A0 |_|8 17|_| D7 <-->
_| |_
<--> D0 |_|9 16|_| D6 <-->
_| |_
<--> D1 |_|10 15|_| D5 <-->
_| |_
<--> D2 |_|11 14|_| D4 <-->
_| |_
GND |_|12 13|_| D3 <-->
|______________________|
Get your own Free Home Page